Adafruit HUZZAH CC3000 WiFi Breakout with Onboard Antenna - v1.1

SKU: ADA1469 Brand: Adafruit

Retired Product

Replaced by: ADA2999
This product has been replaced by: ADA2999
This product is no longer available. This page is only for reference.

For years We've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So Adafruit shied away from carrying any general purpose microcontroller-friendly WiFi boards.

NO LONGER! The CC3000 hits that sweet spot of usability, price and capability. It uses SPI for communication (not UART!) so you can push data as fast as you want or as slow as you want. It has a proper interrupt system with IRQ pin so you can have asynchronous connections. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP & AES. A built in TCP/IP stack with a "BSD socket" interface. TCP and UDP in both client and server mode, up to 4 concurrent sockets. It does not support "AP" mode, it can connect to an access point but it cannot be an access point.

New! As of 3/20/2014 Adafruit are shipping v1.1 which adds a tri-state buffer to the MISO pin so that you can use the CC3000 with other SPI devices on the same bus.

Adafruit wrapped this little silver modules in a tidy breakout board. It has an onboard 3.3V regulator that can handle the 350mA peak current, and a level shifter to allow 3 or 5V logic level. The antenna layout is identical to TI's suggested layout and Adafruit are using the same components, trace arrangement, and antenna so the board maintains its FCC emitter compliance (you'll still need to perform FCC validation for a finished product, but the WiFi part is taken care of). Even though it's got an onboard antenna Adafruit were pretty surprised at the range, as good as a smartphone's.

Each order comes with one fully assembled and tested breakout and a small stick of header you can use to solder in and plug into a breadboard. Adafruit don't have a detailed tutorial yet but to get you started, Adafruit have got a fully working Arduino library that is based off of TI's codebase but adapted for use with the AVR. We also have example code showing how to scan the SSID's, connect to your access point and run DHCP, do a DNS lookup to IP address, ping a site and connect to a remote TCP socket such as a website and print out the page.

Please note the hardware is good, but the library code does not yet support all of the CC3000's functionality. At this moment, SSID scanning, connection, DHCP, DNS lookup, ping, and UDP/TCP client & TCP server connections (eg connect to a website and grab data or host a very short website) all work and are tested with example code. Check out Adafruit's tutorial for wiring and Arduino library downloads

For use with Arduino Uno, Leonardo/Micro & Mega only at this time - we'll try to get the code ported to the Due at some point but no ETA.



Adafruit CC3000 Breakout with Onboard Ceramic Antenna (0:16)

Technical Details

List of wifi access points used to test the CC3000 (by TI, not verified by Adafruit)
 

This product is listed in:

Retired

Product Comments

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

  • $3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
  • $6+ for Standard Post (typically 6+ business days, tracked)
  • $10+ for Express Post (typically 2+ business days, tracked)
  • Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

  • $11+ for Pack and Track (3+ days, tracked)
  • $16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review

Guides

The Maker Revolution

The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...

Projects

Raspberry Pi Video Looper Display Installation | Overshare Video Festival

IntroductionA suspended ceiling display of forty repurposed screens and displays, each screening cr...
IntroductionA suspended ceiling display of forty repurposed screens and displays, each screening cr...

Mailbox Delivery Notification System

Introduction During the Covid lockdown, I needed something to do. The Postman or woman does not de...
Introduction During the Covid lockdown, I needed something to do. The Postman or woman does not de...

PiicoDev Schematic System

Introduction: Hi everybody. Over the past few weeks, I have been working on an intuitive system th...
Introduction: Hi everybody. Over the past few weeks, I have been working on an intuitive system th...
Feedback

Please continue if you would like to leave feedback for any of these topics:

  • Website features/issues
  • Content errors/improvements
  • Missing products/categories
  • Product assignments to categories
  • Search results relevance

For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.

Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.

Makers love reviews as much as you do, please follow this link to review the products you have purchased.